Are air filters too thick?

Most air filters are 1 inch thick, but some systems can accommodate filters 2 to 5 inches thick. In our tests, we found that the thicker the filter, the better it works and the longer the replacement intervals. That means it’s better for you and for your heating, ventilating, and air conditioning (HVAC) system.

Why are some air filters thicker than others?

A thicker filter (4-5 inches) has more surface area and therefore allows more room for air to pass through. Thick filters, due to their increased surface area, also have other benefits like: Higher dust-holding ability (meaning it can catch a lot without blocking airflow)

Can your air filter be too restrictive?

Burnt out motors and controls can result from too-restrictive filters. … Coils, motors, and blowers can also easily become clogged by weak filters creating higher fan usage resulting in higher energy costs.

Can I use a thinner air filter?

If you measure the filter slot, and it’s large enough to accommodate the thicker filter, then you can use it. However, if the slot is less than 4 inches wide, you’re stuck with using that thickness.

IMPORTANT:  Question: Do K&N filters need to be oiled?

Is a MERV 13 filter too restrictive?

MERV 13 air filters are the highest-rated air filters for home use. Any air filter with a rating higher than 13 will restrict air flow to the point of which could cause damage to your HVAC system, resulting in an added expense to fix it.

What if my air filter is too big?

Air Filter Problems with Poor Fit

If you purchase a filter that’s too large, it won’t slide into the slot correctly. If the filter is too small, it won’t cover the entire space and may allow dust and dirt to flow past.

Is MERV 13 bad for HVAC?

Filters within a MERV rating of 17-20 are almost never necessary in a residential home. A MERV rating of 13-16 is considered hospital level air quality, so it is unlikely your home needs any more than that.

Is MERV 13 too high for residential?

One factor to consider is air flow through the system. … In some cases, using an air filter that is too restrictive for your system may cause low air flow problems as well. MERV 13 is the highest MERV value safe for residential furnaces; the higher ratings are used primarily in commercial units.

Is MERV 11 bad for HVAC?

A MERV 11 air filter has a higher efficiency rating. … In particular, using an air filter with a MERV rating that’s too high can damage the compressor, heat exchanger, and air conditioner coil. In most cases, a MERV 11 air filter isn’t too high for residential use.

What MERV rating can my HVAC handle?

The EPA recommends MERV ratings of 9-12 because it is the most effective at keeping your home’s air clean. A filter with this rating will prevent particulates as small as 1 micron from entering your HVAC system. This rating qualifies as HEPA (high-efficiency particulate absorption) level.

IMPORTANT:  What size filter do I need for a 100 gallon aquarium?

Does width of air filter matter?

Does Size Matter? You’ve guessed it! The answer is yes. It is essential to use the right size air filter for your HVAC unit to keep your system running smoothly and to reap all the benefits your air filter has to offer.

Does thickness of furnace filter matter?

The Thicker, the Better

Furnace filters can range anywhere from 1″to 5″ in thickness. In general, the thicker the furnace filter is the more efficiently your unit work and the longer it will last.

Can I use a 2 inch filter instead of 1 inch?

As you can see the 2 inch filter will serve our needs MUCH better than the 1 inch filter. Even if the duct system is in good shape, using this filter will keep the system from struggling.

Is FPR and MERV the same?

MERV ratings extend from 1 to 16. MPR measures ratings based on sizes 0.3 to 1 microns. FPR ratings are on a scale from 4 through 10. The MERV filter rating is the domestic and international industry standard rating system established by the American Society of Heating, Refrigerating, and Air Conditioning Engineers.

Whats the difference between MERV 11 and 13?

A MERV 11 rated furnace filter can trap the majority of harmful contaminants that are present in the air. … A MERV 13 filter is capable of filtering out all particle impurities like dust, lint, pollen, mold, dust mites, pet dander, smog, and smoke. On top of this, it can also trap bacteria and viruses.

What MERV rating is HEPA?

All HEPA filters have a rating of a MERV 17 or higher. A HEPA filter with a MERV 17 rating will trap 99.97% of air particles that are 0.3-1.0 micron in size and an even better % of particles below 0.3 microns and above (HEPA filters are rated at their worst performance).

IMPORTANT:  Will a water filter get rid of sulfur smell?